Copy of EVERCOAT Hail Damage SOP Quiz

Copy of EVERCOAT Hail Damage SOP Quiz

Time limit: 0

Quiz Summary

0 of 19 Questions completed

Questions:

Information

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading…

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 19 Questions answered correctly

Your time:

Time has elapsed

You have reached 0 of 0 point(s), (0)

Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)

Categories

Not categorized 0%

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

Current
Review
Answered
Correct
Incorrect

Question 1 of 19

1. Question
It is only necessary to clean when contaminants are visible.
- True
- False
Question 2 of 19

2. Question
Which of the following EVERCOAT Polyester Primers do not require a pre-coat for corrosion protection.

(Select all that apply)
- Finish Sand 4:1
- OPTEX Super Build 4:1
- Super Build 4:!
- All of the above
- None of the above
Question 3 of 19

3. Question
The entire panel should be cleaned prior to the repair.
- True
- False
Question 4 of 19

4. Question
When additional working time is required due to high temperatures, or for larger applications that Rage® Ultra XTRA may be mixed in with Rage Ultra and Optex.
- True
- False
Question 5 of 19

5. Question
When using OPTEX Super Build it is required to sand off all of the pink guide coat before coating.
- True
- False
Question 6 of 19

6. Question
Technician A says that it is ok to apply EVERCOAT Rage Ultra/Optex over properly sanded OEM paint. Technician B says that all Evercoat fillers should be applied to bare metal only. Who is correct?
- Technician A
- Technician B
- Both
- Neither
Question 7 of 19

7. Question
EVERCOAT Rage Ultra/Optex can be applied over properly sanded OEM paint.
- True
- False
Question 8 of 19

8. Question
The easiest way to measure 2% BPO (cream hardener) is to apply a ribbon completely across a puddle of filler that is:
- 2 inches in diameter
- 3 inches in diameter
- 4 inches in diameter
- None of the above
Question 9 of 19

9. Question
Applying Rage Ultra or Optex over properly sanded OEM Paint, factory primer or factory E-coat minimizes compromising the factory corrosion protection and is best for the repair.
- True
- False
Question 10 of 19

10. Question
Rage® Ultra XTRA can be used with Evercoat Premium Putties to increase viscosity and extend working time in high heat applications.
- True
- False
Question 11 of 19

11. Question
The recommended final finish sanding step for 440 Express Pinhole Eliminator before applying a solvent based primer is:
- Lightly scuffed with a red scuff pad
- Lightly scuffed with a gray scuff pad
- Lightly scuffed with 320-400 by hand
- No sanding is required when applying a solvent based primer
Question 12 of 19

12. Question
The viscosity of Evercoat Putties can be adjusted by mixing with an Evercoat Filler and/or Rage® Ultra XTRA.
- True
- False
Question 13 of 19

13. Question
What is the final grit specified for the EVERCOAT Polyester Primers at the end of each video?
- 220 grit
- 320 grit
- 180 grit
- Finish sand and coat to your paint manufacturer’s recommendations
Question 14 of 19

14. Question
The EVERCOAT recommended final finish sanding step for Rage Ultra and Rage Optex is:
- 80 Grit DA
- 120Grit DA
- 180 Grit DA
- 220 Grit DA
Question 15 of 19

15. Question
Evercoat recommends applying polyester putty in all the following manners except:
- All at once with moderate pressure
- With even form pressure out over and onto the featheredge
- Apply additional material as needed
- Thin tight pressure to wet the repair surface
Question 16 of 19

16. Question
Technician A says that the preferred pre-coat before applying an EVERCOAT 4:1 Polyester Primer is an epoxy primer. Technician B says that the preferred pre-coat before applying an EVERCOAT 4:1 Polyester Primer is a self-etch primer.

Who is correct?
- Technician A
- Technician B
- Both
- Neither
Question 17 of 19

17. Question
Using the EVERCOAT repair process will minimize damage to the factory corrosion protection.
- True
- False
Question 18 of 19

18. Question
Evercoat Rage Ultra and Optex are recommended to be catalyzed at what percentage / ratio?
- 1% – 50:.5 [100:1]
- 2% – 50:1 [100:2]
- 3% – 50:1.5 [100:3]
- 4% – 50:2 [100:4]
Question 19 of 19

19. Question
When using 440 Express with a solvent based primer to wait 10 minutes and that sanding is not required.
- True
- False